|
Operating Data |
| Power Supply |
|
| Input Power |
100~240 VAC |
| Input Connector |
IEC Inlet C14 |
| Power Consumption |
45W Max |
| Additional information |
Isolated Supply and Chassis Ground |
| Power supply options |
48V VDC Power Input
Dual Power Supply |
Operating Environment |
| Operating Temperature |
0°C to 45°C
-15°C to 50°C (Optional Extended Range) |
| Storage Temperature |
-10°C to 70°C
-40°C to 70°C (Optional Extended Range) |
| Operating Humidity |
15% to 85% RH |
| Storage Humidity |
5% to 90% RH |
| MTBF |
> 100,000 Hrs |
Features |
| Connectivity and Networking |
|
| Network type |
Fast Ethernet (802.3u) |
| Network connector |
RJ45 |
| Link speeds |
10/100 Mbps with auto negotiation |
| Network indications |
Network Link LED (Green),
10/100 Mbps LED (Yellow) |
Sensors |
| Number of inputs |
12 |
| Input Connector |
RJ11 - 6/4 |
| Parameters monitored |
Temperature, Humidity, Open / Close contacts |
| Temperature Monitoring Range |
0°C to 60°C |
| Temperature Monitoring Accuracy |
± 5% Standard Transducer @ 20°C |
| Temperature Hysteresis |
Programmable 0.1°C to 9.9°C in 0.1 increments |
| Humidity Monitoring Range |
30% to 90% Relative Humidity |
| Humidity Monitoring Accuracy |
± 5% RH @ 25°C |
| Humidity Hysteresis |
Programmable 0.1%RH to 9.9%RH in 0.1 increments |
| Analogue Resolution |
12 Bit A/D |
| Additional Information |
Inputs are not isolated
Auto detection of supported Sinetica sensors |
| PDU (power strip) Monitoring and Control |
|
| Number of inputs |
6 |
| PDU Input connector |
RJ11 - 6/6 |
| Parameters monitored |
Voltage, Current, kilo-Watt hours (kWh), kilo volt-Ampere (kVA) |
| Voltage monitoring range |
0 V to 500 V |
| Voltage monitoring accuracy |
± 2% |
| Current Monitoring range |
0 A to 65 A |
| Current Monitoring accuracy |
± 2% |
| Kilo Watt-hours Monitoring range |
0 kWh to 429496729 kWh |
| Kilo Watt-hours Monitoring accuracy |
Dependent on PDU |
| Kilo volt-Ampere Monitoring range |
0 kVA to 429496729 kVA |
| Kilo volt-Ampere Monitoring accuracy |
N/A |
| Output relays |
|
| Number of outputs |
4 |
| Output Connectors |
Screw lock WeidMuller (Outputs 1 & 2)
Screw lock Phoenix Contact (Outputs 3 & 4) |
| Output Modes |
Normally Open, Normally Closed |
| Maximum Switching |
48 V at 1 A (Resistive load) |
| Additional information |
Outputs 1 and 2 offer a 12+ V DC supply fused at 1 amp |
| Monitoring and Configuration |
|
The following monitoring and configuration
methods are provided: |
Web management interface via HTTP or HTTPS (secure)
SNMP |
| LCD Status Monitor |
|
The optional backlit LCD status monitor
can display the following: |
Summary page displaying configured PDUs and Inputs 1 and 2.
All 12 Digital Inputs
All 6 PDUs |
The following system information
is also available: |
Firmware Version
IP Address
Subnet Mask
Gateway
MAC Address |
| Additional information |
Backlit
Power from unit (no additional power source required.) |
| Status Indicators |
|
Unit front panel provides the following
LED indications |
Power (Green)
Status (Green)
Network Link (Green)
Network Speed (Yellow)
Digital Output (Yellow)
Analogue Input (Red)
Digital Input (Red) |
-1.jpg)
